Images are representations only.
8076 Positive Displacement Flowmeter
Brand: Burkert Fluid Control Systems
This positive displacement flowmeter with display Type 8076 is designed for use in highly viscous fluid like glue, honey. It is made up of a compact sensor fitting (S070) and an enclosure with cover, containing the electronic module. A removable display completes the flowmeter. This ensemble (SE36) is quickly and easily connected to the sensor fitting (S070) by a Quarter-Turn.
The flowmeter can operate without the display, but it will be required for configuring the flowmeter (i.e. set parameters, restore default parameters, configure information to be displayed, programme access code, adjust 4-20 mA output(s) and also for visualizing continuously the measured and processed data.
Features- Configurable outputs: one or two transistor output(s) and single or dual 4-20 mA current output(s)
- Removable backlit display of flow rate and/or 2 two totalized volumes
- Automatic-calibration: Teach-In, simulation of outputs signals provided without the need for real flow
Specifications
Ambient Temperature Range
- Operating & Storage: 0° to 60° C (32° to 140° F)
Approvals & Certifications
- CE
- EMC: EN 61000-6-2, EN 61000-6-3
- PED 97/23/CE
- UL (C,US): UL 61010-1 + CAN/CSA-C22.2 No.61010-1
Cable Length
- 164 feet (50 meters), Maximum
Circuit Protection
- Short Circuit Protected for Transistor Outputs
Consumption
- Current (2 or 3 Outputs Flowmeter [2-Wire]): ≤ 25 mA at 14 Vdc without Transistors Load, with Current Loop
- Current (4 Outputs Flowmeter [3-Wire]): ≤ 5 mA at 12 Vdc without Transistors Load, without Current Loop
- Current: ≤ 1 A with Transistor Loads
- Power: 40 W, Maximum
Cover Material
- Polycarbonate
Current
- 4-20 mA
Diameter
- Pipe: 1/2 to 4" (DN15 to DN100)
Display
- Grey Dot Matrix 128 x 64 with Backlighting
Electrical Connectors
- 1.5 mm², Maximum
- 5-Pin M12 Female
- Shielded Cable
Electrical Protection
- Voltage Peak: Protected
Enclosure, Body Material
- 316L Stainless Steel 1.4401
- 316Ti Stainless Steel, 1.4542
- Aluminum
- PPS
Environmental Protection
- IP65
- IP67
Flange Size - 1-1/2" (DN40)
- Unrated
Flange Size - 1" (DN25)
- Unrated
Flange Size - 2" (DN50)
- Unrated
Flange Size - 3" (DN80)
- Unrated
Flange Size - 4" (DN100)
- Unrated
Humidity
- ≤ 80% Relative Humidity, Non-Condensing
Loop Impedance
- 1 Current Output: 180 ohms at 14 Vdc, Maximum
- 1,100 ohms at 36 Vdc, Maximum
- 2 Current Outputs: 100 ohms at 12 Vdc, Maximum
- 610 ohms at 24 Vdc, Maximum
Materials of Construction
- Display, Quarter-Turn System: Polycarbonate (PC)
- Fixed Connector Mounting Plate: 316L Stainless Steel, 1.4404
- Fixed Connector: Brass Nickel-Plated
- Fixed Connector: Stainless Steel
- Navigation Key: PBT
Measuring Error
- Measurement Deviation: ± 0.5% of Reading
Measuring Range
- Viscosity 5 MPa.s: 2 to 1,200 L/minute
Operating Voltages
- 2 or 3 Outputs Flowmeter (2-Wire): 14-36 Vdc, Filtered & Regulated
- 4 Outputs Flowmeter (3-Wire): 12-36 Vdc, Filtered & Regulated
Output
- 1 Transistor Output, 2 Transistor Outputs (NPN): 1-36 Vdc
- 2 Transistor Outputs: 0.5 A, Maximum
- 4-20 mA, 2 & 3-Wire
- Transistor: 700 mA - Maximum
Output Format
- Open Collector
Pressure Range
- bar: 0 to 55
- kPa: 0 to 5,500
- psi: 0 to 798
Process Temperature
- Aluminum Body: 0° to 80° C (32° to 176° F)
- Stainless Steel Body: 0° to 100° C (32° to 212° F)
Repeatability
- ≤ 0.03% of Reading
Reverse Polarity Protection
- Yes
Screw Material
- Stainless Steel
Seat / Seal Material
- Seal: EPDM
- Seal: FEP
- Seal: FKM
- Seal: PTFE
Shaft Material
- Stainless Steel
Shock
- EN 60068-2-27
Switch Type
- 1 Transistor Output (NPN), 2 Transistor Outputs (NPN & PNP): Transistor
Vibration
- EN 60068-2-6
Viscosity
- 5 MPa.s
- 1 Pa.s, Maximum
Wetted Materials
- Rotor: 316L Stainless Steel (1.4401)
- Rotor: Aluminum
- Rotor: PPS
